If motherboard fails or an upgrade to a faster CPU or memory needs newer motherboard then old motherboard is replaced. New motherboard should be compatible with form factor, SMPS and other devices. Driver software may be needed for proper working of devices.<\/p>\n\n\n\n
Removing Motherboard<\/strong><\/p>\n\n\n\n First, power off and disconnect every cable from the outside of PC. Use anti-static device to open chassis cover and disconnect all cables inside the chassis. Remove the drive cage if needed and any remaining cables and all cards in expansion slots and place them on an anti-static surface. Leave CPU and memory in their places and remove the screws holding the motherboard to the case, and carefully remove the motherboard. Place CPU and memory on the anti-static surface.<\/p>\n\n\n\n Installing Motherboard<\/strong><\/p>\n\n\n\n Check for correct voltage of SMPS for new motherboard. No conductive surface should come in contact with any metal parts of the chassis. Chassis may have elevated mounting holes that hold the board away from the case wall or standoffs which are small spacers that are between board\u2019s and case\u2019s mounting holes. After screwing in the screws, install the power connectors and reinstall all of the peripheral devices which were connected to the old motherboard.<\/p>\n\n\n\n Motherboard Setup<\/strong><\/p>\n\n\n\n Motherboards have stickers indicating DIP switches and jumpers which are illustrated in the motherboard manual or at manufacturer\u2019s Web site.<\/p>\n\n\n\n Depending on the board, settings can be done by jumpers or DIP switches or CMOS setup according to the speed and family of the processor, and there might also be jumpers to reset the CMOS, redirect the sound from the rear to front connectors, select the type of memory to install, and others.<\/p>\n\n\n\n Motherboard Maintenance<\/strong><\/p>\n\n\n\n Maintenance involves download and install of new driver for motherboard from manufacturer\u2019s website and replacing CMOS battery if computer does not saves BIOS configuration during reboots.<\/p>\n\n\n\n Flashing BIOS<\/strong><\/p>\n\n\n\n Upgrading the programme in ROM BIOS by downloading and installing is called flashing BIOS or flashing ROM or updating the BIOS. BIOS manufacturer gives update on website to download.<\/p>\n\n\n\n CMOS Menu configuration<\/p>\n\n\n\n It involves selecting options in CMOS setup utility under various heads and options are<\/p>\n\n\n\n Standard Settings<\/strong><\/p>\n\n\n\n Date and time- Sets the system date and time and Operating System pick it when it starts up.<\/p>\n\n\n\n Keyboard – if the keyboard is installed or not if don\u2019t want someone changing settings.<\/p>\n\n\n\n BIOS Feature Settings<\/strong><\/p>\n\n\n\n Quick boot (Enable\/disable) – Enable to cause POST to skip some tests and speed up booting. System boot sequence – Sequence to look for Operating System in hard disk\/CD\/USB\/Network<\/p>\n\n\n\n Password – Set a startup password to prevent someone from using PC.<\/p>\n\n\n\n Plug and Play – Disable for Windows 2000\/XP, which does it them self<\/p>\n\n\n\n Advanced Chipset Settings<\/strong><\/p>\n\n\n\n Audio controller – Enable or disable<\/p>\n\n\n\n USB configuration – Enable or disable and sets to high speed or legacy speed.<\/p>\n\n\n\n CPU configuration – Enable or disable Hyper Threading and Sets thermal control.<\/p>\n\n\n\n Power Management Settings<\/strong><\/p>\n\n\n\n Suspend mode (Enable\/disable) – suspending power when the system is inactive<\/p>\n\n\n\n Wake on LAN – Allows PC to boot from another PC on same network but needs an ATX SMPS.<\/p>\n\n\n\n Hard Drive Settings<\/strong><\/p>\n\n\n\n IDE HDD auto detect – Detects hard disks installed on IDE channel set to auto detect.<\/p>\n\n\n\n Serial ATA – Configure to IDE or RAID.<\/p>\n\n\n\n Hardware Device Settings<\/strong><\/p>\n\n\n\n Processor operating speed – Sets the CPU speed and used for throttling and overclocking.<\/p>\n\n\n\n External clock – Sets the system bus speed.<\/p>\n\n\n\n Boot Settings<\/strong><\/p>\n\n\n\n Boot device priority Sets the boot sequence.<\/p>\n\n\n\n Exit Menu<\/strong><\/p>\n\n\n\n Exit – Options to exit and save changes, exit and discard changes, or discard changes and not exit.<\/p>\n\n\n\n Load default settings – Return BIOS setup to factory default settings.<\/p>\n\n\n\n https:\/\/www.vskills.in\/certification\/certified-it-support-professional<\/a><\/p>\n\n\n\n If motherboard fails or an upgrade to a faster CPU or memory needs newer motherboard then old motherboard is replaced. New motherboard should be compatible with form factor, SMPS and other devices. Driver software may be needed for proper working of devices. Removing Motherboard First, power off and disconnect every cable from the outside of…<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"categories":[127],"tags":[],"class_list":["post-110316","page","type-page","status-publish","hentry","category-it-support-professional"],"acf":[],"yoast_head":"\nApply for IT Support Certification<\/strong><\/h2>\n\n\n\n
Back to Tutorials<\/a><\/strong><\/h4>\n","protected":false},"excerpt":{"rendered":"